A Power and Thermal Analysis of A Pcm-Cooled Photovoltaic Thermal System With A 1-D Mathematical Model for Different Environmental and Boundary Conditions: A Case Study

##plugins.themes.academic_pro.article.main##

Erkan Ökten
Levent Kırcı
Özgür Kılıçlı

Abstract

Reducing the PV panel temperature significantly increases the PV panel efficiency. The most important parameters affecting the temperature of the PV panel are; environmental temperature, wind speed, sunbathing time, and irradiation. Although there are many methods for PV panel cooling, one of the most common methods is to cool the panel by placing PCM material on the PV panel's bottom surface.  In this study, PV/PCM integration under different boundary conditions was investigated with a 1-D mathematical model. In the study, environmental conditions were determined using real meteorological data, and the results were shared for four seasons. The mathematical model was performed for the conventional PV model, the PV/PCM integrated model, and the integrated PV/PCM which the base is kept at a constant temperature. As a constant temperature value, 10, 15, and 20 oC were chosen. The results were analyzed in terms of PV temperature, PCM melting rate, electricity production, energy absorbed by PCM, and thermal and electrical efficiency. If the annual performances are examined, the maximum electricity production is 263000 kW for the case where the PV/PCM base is kept constant at 10 degrees, and this value is 1200 kW higher than the traditional PV panel. The maximum absorbed energy by PCM was obtained as 26990 kW for the PV/PCM integration.

##plugins.themes.academic_pro.article.details##

How to Cite
Ökten, E., Kırcı, L., & Kılıçlı, Özgür. (2022). A Power and Thermal Analysis of A Pcm-Cooled Photovoltaic Thermal System With A 1-D Mathematical Model for Different Environmental and Boundary Conditions: A Case Study. International Journal of Pioneering Technology and Engineering, 2(02), 193–201. https://doi.org/10.56158/jpte.2023.57.2.02

References

  1. Abdulmunem, A. R., Samin, P. M., Rahman, H. A., Hussien, H. A., Mazali, I. I., & Ghazali, H. "Numerical and experimental analysis of the tilt angle’s effects on the characteristics of the melting process of PCM-based as PV cell’s backside heat sink." Renewable Energy, 173, 520-530,2021.
  2. Abdulmunem, A.R. "Passive cooling by utilizing the combined PCM/aluminum foam matrix to improve solar panels performance: indoor investigation," Iraqi J. Mech. Mater. Eng 17(4): 712-723,2017.
  3. Huang, M. J., Eames, P. C., & Norton, B. "Thermal regulation of building-integrated photovoltaics using phase change materials." International Journal of heat and mass transfer, 47(12-13), 2715-2733,2004
  4. Bilgen, E. "Passive solar massive wall systems with fins attached on the heated wall and without glazing."J. Sol. Energy Eng., 122(1), 30-34, 2000.
  5. Goossens, D., & Van Kerschaever, E. "Aeolian dust deposition on photovoltaic solar cells: the effects of wind velocity and airborne dust concentration on cell performance." Solar energy, 66(4), 277-289,1999.
  6. Emam, M., & Ahmed, M. "Cooling concentrator photovoltaic systems using various configurations of phase-change material heat sinks." Energy conversion and management, 158, 298-314,2018.
  7. Ling, Z., Zhang, Z., Shi, G., Fang, X., Wang, L., Gao, X., ... & Liu, X. "Review on thermal management systems using phase change materials for electronic components, Li-ion batteries and photovoltaic modules." Renewable and Sustainable Energy Reviews, 31, 427-438,2014.
  8. Ma, T., Li, Z., & Zhao, J. "Photovoltaic panel integrated with phase change materials (PV-PCM): technology overview and materials selection." Renewable and Sustainable Energy Reviews, 116, 109406,2019.
  9. Armstrong, S., & Hurley, W. G. "A thermal model for photovoltaic panels under varying atmospheric conditions." Applied thermal engineering, 30(11-12), 1488-1495,2010.
  10. Smith, C. J., Forster, P. M., & Crook, R. "Global analysis of photovoltaic energy output enhanced by phase change material cooling." Applied energy, 126, 21-28,2014.
  11. Stritih, U. "Increasing the efficiency of PV panel with the use of PCM." Renewable Energy, 97, 671-679, 2016.
  12. Khanna, S., Reddy, K. S., & Mallick, T. K. "Performance analysis of tilted photovoltaic system integrated with phase change material under varying operating conditions." Energy, 133, 887-899,2017.
  13. Savvakis, N., & Tsoutsos, T. "Theoretical design and experimental evaluation of a PV+ PCM system in the mediterranean climate." Energy, 220, 119690, 2021.
  14. Ahmadi, R., Monadinia, F., & Maleki, M. " Passive/active photovoltaic-thermal (PVT) system implementing infiltrated phase change material (PCM) in PS-CNT foam." Solar Energy Materials and Solar Cells, 222, 110942,2021.
  15. Duan, J. "The PCM-porous system used to cool the inclined PV panel."Renewable Energy, 180, 1315-1332,2021.
  16. Ashouri, M., & Hakkaki-Fard, A. "Improving the performance of the finned absorber inclined rooftop solar chimney combined with composite PCM and PV module." Solar Energy, 228, 562-574,2021.
  17. Khodadadi, M., & Sheikholeslami, M. " Numerical simulation on the efficiency of PVT system integrated with PCM under the influence of using fins." Solar Energy Materials and Solar Cells, 233, 111402,2021.
  18. Khanna, S., Reddy, K. S., & Mallick, T. K. " Optimization of finned solar photovoltaic phase change material (finned pv pcm) system." International Journal of Thermal Sciences, 130, 313-322,2018.
  19. Kumar, K. S., Kumar, H. A., Gowtham, P., Kumar, S. H. S., & Sudhan, R. H. "Experimental analysis and increasing the energy efficiency of PV cell with nano-PCM (calcium carbonate, silicon carbide, copper)."Materials Today: Proceedings, 37, 1221-1225,2021.
  20. Stalin, P. M. J., Prasad, K. S., Kumar, K. P., Hemadri, G., Rajesh, M., & Kumar, K. P. " Performance improvement of solar PV through the thermal management using a nano-PCM."Materials Today: Proceedings, 50, 1553-1558,2022.
  21. Kurşun, B., & Ökten, K. "Thermodynamic analysis of a Rankine cycle coupled with a concentrated photovoltaic thermal system for hydrogen production by a proton exchange membrane electrolyzer plant."International Journal of Hydrogen Energy, 44(41), 22863-22875,2019.
  22. Cengel, Y.A. and Ghajar, A.J.J.A.p.a., 2007, Heat and mass transfer,2007
  23. Chow, T. T. "Performance analysis of photovoltaic-thermal collector by explicit dynamic model."Solar Energy, 75(2), 143-152,2003.
  24. Jiji, L. M., & Gaye, S. "Analysis of solidification and melting of PCM with energy generation." Applied Thermal Engineering, 26(5-6), 568-575,2006.